Jm Storm Tracker 2 Track system (2011 & newer) Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Hardware Jm Storm Tracker 2 Track system (2011 & newer). J&M Storm Tracker 2 Track system (2011 & newer) User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 16
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
J. & M. Manufacturing Co., Inc.
P.O. Box 547
Fort Recovery, OH 45846
Phone: (419) 375 2376 Fax: (419) 375-2708
E-mail: [email protected] Website: www.jm-inc.com
Storm Tracker Track System
FRONT
REV 7.18.2014
O P E R A T O R’ S M A N U A L
Zobrazit stránku 0
1 2 3 4 5 6 ... 15 16

Shrnutí obsahu

Strany 1 - Storm Tracker Track System

J. & M. Manufacturing Co., Inc.P.O. Box 547Fort Recovery, OH 45846Phone: (419) 375 2376 Fax: (419) 375-2708E-mail: [email protected] Websit

Strany 2 - To The Dealer

10IStep 1 - Install both spindles. Use (2) 1” x 9” Hex Bolts and (2) 1” Centerlock Hex Nuts to attach the spindles to the cart. Next slip t

Strany 3

11IStep 4 - Slide the tracks onto the spindle. Step 5 - Slip the 6” Rubber O-Ring onto the spindle, pushing it up against the track spindl

Strany 4

12P

Strany 5

13P# Description Part. No.1 2-1/2” ID Bronze Bushing JM00168412 Bogie Wheel Swivel Weldment JM00202563 1”-8 Gr5 Z Centerlock Hex Nut JM00021494 1”

Strany 6

14TITLEP

Strany 7

15TITLE# Part. No. Description1 JM0020273 Track Carriage Beam Frame Weldment2 JM0020350 6” ID Bronze Bushing3 JM0016687 1”-8 X 4-1/2” Gr5 Z Hex Bolt4

Strany 8

16NDATE NOTE

Strany 9

2To The DealerTO THE DEALER:Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in t

Strany 10

3TITLETo The Dealer SpecificaTionSABCSpecicationsTrack Width 36”Idler Width (eective) 36”Overall Length (A) 146”Idler Diameter 36”Roller Diameter 12

Strany 11

4General inforTmaTionBOLT TORQUE CHARTAlways tighten hardware to these values unless a dierent torque or tightening procedure is listed for a specif-

Strany 12

5SafeTy ruleSGeneral inforTmaTionATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!Safety is a primary concern in the design and manufacture of our p

Strany 13 - # Description Part. No

6SLubrication Service ScheduleIMPORTANT: Your Track System has grease ttings at all critical points. ese should be serviced before the track i

Strany 14 - TITLEP

7R MWARNING: When Servicing e Track System, Be Certain All Power To Grain Cart Is Shut O.Repack the wheel bearings at least once a

Strany 15

8SAIR BAG REPLACEMENTIf replacement of the track tension air springs become necessary, the following steps must be performed:1. Slowly release

Strany 16 - DATE NOTE

9SBELT INSPECTIONe rubber track is composed of several layers of cable, similar to the cables used in automotive tires. e most important set

Komentáře k této Příručce

Žádné komentáře